home | tech | search | checkout | contact | email | forum   

 

 

 

 

 

 

 

 




Classic Inlines
603 W Pecos Ave
Mesa, AZ 85210
(602) 708-6650
9am-5pm (PST)
Monday-Friday
INTERNET-PHONE SALES ONLY

NO WALK-INS

Sorry We don't have a store front







 
Dyno Test #6

Our first step was to establish our baseline numbers with the stock 1100 carb and the Load-O-Matic distributor. Once that was accomplished, we install the Weber 32/38 progressive two barrel carb using the 2-1 adaptor and made another pull on the dyno. Next, we pulled the stock dizzy and dropped the DUI in its place, using a relay so it got a full 12 volts from the battery. After a run with the Weber and the DUI, we installed the Autolite 240cfm, did two more pulls, then installed the Holley 350cfm and did two more pulls. Our final pass was with a used Autolite 245cfm, as we wanted to see if the additional 5cfm would make any difference in the numbers.

Remember, both Autolite's were used carbs purchased at a swap meet earlier this summer, so we had no idea of their condition, or if they would even run. To our surprise both worked fine, however it was obvious that the 245cfm needed a rebuild. It also needed to be re-jetted as it was quite lean, however we didn't take time to re-jet as it was time for lunch and the guys were getting anxious to go eat. We got the information we were after using the first three carbs, and considering the last run didn't really matter, we decided to call it a day. Here's the results of the runs made that day, which were pretty close to the results obtained on our first day of testing.

Carb
CFM
Dizzy
Max HP
Max TQ
HP/CFM
Gain
Autolite 1V
180
LOM
62 @ 3900
93 @ 2900
0.34
Base
Weber 2V
300
LOM
70 @ 4300
94 @ 3350
0.23
Base
Weber 2V
300
DUI
85 @ 4900
105 @ 3300
0.28
27 %
Autolite 2V
240
DUI
83 @ 4950
105 @ 3400
0.35
25 %
Autolite 2V
245
DUI
84 @ 4900
105 @ 3300
0.34
26 %
Holley 2V
350
DUI
87 @ 4800
106 @ 3200
0.25
29 %

SUMMARY: All four carbs were within a 4HP range, with the Autolite 240 making the least, and the Holley 350 producing the most. Even in its poor condition the Autolite 245 made nearly as much as the Weber, yet both produced slightly less than the Holley. The torque was nearly identical for all four carbs. Eventually, I'd like to try an Autolite 351 or a 356 to see how they'd compare to the Holley 350, as the horsepower appears to be directly relational to the size of the carb. Assuming the Autolite carbs were to small, and the fact that all three Autolite's made an average of .345HP per cfm (as compared to the Weber and Holley at .25 and .28 respectively), then an Autolite 356 would produce around 123HP (356x.345=123). While logic tells me this is doubtful, it's certainly worth investigating, and we'll be sure to let you know how it works out if we get the opportunity to test one. In the end, the Holley and DUI were worth a net gain of 25 HP and 13 LBS of torque over the stock carburetor and distributor, which resulted in a 29% gain in rear wheel horsepower. Remember, this motor was recently rebuilt and already had a performance cam and headers. Once the engine is broken in and the rings fully seated, I'm guessing the numbers will be slightly better.

One problem we noticed was that the motor seemed sluggish below 2500 rpm, but once it got going it seemed to accelerate much better. I'm guessing the cam timing is retarded, maybe by as much as 6-8 degrees, as it wasn't degreed when it was installed. Clay Smith recommends installing the cam 4 degrees advanced, as their cams are ground straight up, therefore it's at least 4 degrees off. However I'm guessing it's even more, based on how sluggish the motor was, as an inline six should make considerably more bottom end power.

The owner plans to replace the damper sometime in the near future, which would be be the perfect opportunity to degree the cam. If I'm right and the cam is off, I'd like to take it back for another pull on the dyno to see how it effects the overall performance, and our numbers. It would also be a good time to test an Autolite 356? If we retest, we'll be sure to let you know how it works out.

 
Baseline
 
Holley-Autolite-Weber



Dyno:
#1 - #2 - #3 - #4 - #5 - #6 - #7 - #8 - #9 - #10
Track:
#1 - #2 - #3 - #4 - #5 - #6 - #7 - #8 - #9 - #10




home ] [ index ] [ products ] [ search ] [ checkout ]

Copyright 2012 - Classic Inlines - All Rights Reserved